Diamond discs
to
cut plastic and materials
Ø |
width. |
ø |
ORDER No |
|
22 |
0,3 |
1,50 |
N 23/022 |
3 |
30 |
1,3 |
6,35 |
N 23/030 |
1 |
50 |
1,6 |
6,35 |
N 23/050 |
1 |
75 |
1,6 |
6,35 |
N 23/075 |
1 |
100 |
2 |
12,7 |
N 23/100 |
1 |
125 |
2 |
22,2 |
N 23/125 |
1 |
mounting |
Max. RPM |
||
on mandrel |
L50/111 |
shaft of 3 mm |
75.000 |
on mandrel |
L50/105 |
shaft of 6 mm |
70.000 |
on mandrel |
L50/105 |
shaft of 6 mm |
38.000 |
on mandrel |
L50/105 |
shaft of 6 mm |
22.000 |
on mandrel L 50/104 shaft of 6 mm |
14.000 |
||
on angle grinder |
12.000 |
||
D427 |
The mandrels are sold per unit |
Diamond bores
Ø |
cutting profoundness |
ø |
|
12 |
32 |
8 |
N 24/012 |
16 |
32 |
8 |
N 24/016 |
20 |
32 |
8 |
N 24/020 |
25 |
32 |
8 |
N 24/025 |
35 |
32 |
10 |
N 24/035 |
50 |
32 |
10 |
N 24/050 |
D151
to cut out in
all materials, pavings, eternit, fibre-cement, porcelain, glass,
marble, earthenware, ceramic, … but also in synthetic materials
such as polyester, fibre-glass, plastic, …
Fine and precise
cut.
ALWAYS wet use, at a speed close to 300
up to 800 RPM and preferably - for more precision - on a drill press.
Crowns in tungsten carbide
Ø |
cutting profoundness |
ø |
ORDER No |
33 |
50 |
10 |
N 25/133 |
53 |
50 |
10 |
N 25/153 |
63 |
50 |
10 |
N 25/163 |
73 |
50 |
10 |
N 25/173 |
83 |
50 |
10 |
N 25/183 |
the crowns are charged with tungsten carbide grit of 0,8 up to 1,2 mm to cut out in bricks, blocs, eternit, pavings, fibre-cement, polyester, fibreglass, ...
Aggressive cut - less precisely - than when working with the diamond bores.
Rough cutting with dry or wet use, at low speed.
Set of 4 crowns
supplied with a hexagonal shaft of 10mm,mounting plate and centring
pilot shaft.
Ø 33, 53, 63 and 73 mm N 25/075
Files
shapes |
sharpened surface |
total length in mm |
cuts |
|
||
MEDIUM |
FINE |
EXTRA-FINE |
||||
rectangular |
6 x 1,3 x 90 |
180 |
N 10/003 |
N 10/005 |
N 10/007 |
1 |
22 x 5 x 180 |
250 |
N 10/013 |
N 10/015 |
N 10/017 |
1 |
|
triangular |
3,9 x 90 |
180 |
N 10/103 |
N 10/105 |
N 10/107 |
1 |
14 x 180 |
250 |
N 10/115 |
N 10/117 |
1 |
||
square |
3 x 3 x 90 |
180 |
N 10/203 |
N 10/205 |
N 10/207 |
1 |
8 x 8 x 180 |
250 |
N 10/215 |
N 10/217 |
1 |
||
round |
3,5 x 90 |
180 |
N 10/303 |
N 10/305 |
N 10/307 |
1 |
8 x 180 |
250 |
N 10/315 |
N 10/317 |
1 |
||
half-round |
6 x 2 x 90 |
180 |
N 10/403 |
N 10/405 |
N 10/407 |
1 |
21 x 6 x 180 |
250 |
N 10/415 |
N 10/417 |
1 |
||
|
|
|
|
|||
Number of cut per cm |
20 |
25 |
38 |
|||
