|
Composed of a multitude of little abrasive spheres mounted
on flexible wires.
|
|
|
|
ø min.>max.
to hone
in mm |
total length mm
|
grits |
ORDER No |
3,8 |
> |
4,2 |
155 |
C 180 |
L 10/001
|
4,3 |
> |
4,5 |
155 |
C 180 |
L 10/002
|
4,6 |
> |
4,9 |
155 |
C 180 |
L 10/003
|
5,0 |
> |
5,1 |
200 |
C 180 |
L 10/004
|
5,1 |
> |
5,5 |
200 |
C 180 |
L 10/005
|
5,6 |
> |
6,4 |
200 |
C 180 |
L 10/006
|
6,5 |
> |
7,0 |
200 |
C 180 |
L 10/007
|
7,1
|
>
|
8,5
|
200
|
C
180 |
L
10/008 |
8,6 |
> |
9,0 |
200 |
C 180 |
L 10/009
|
9,1 |
> |
10,0 |
200 |
C 180 |
L 10/010
|
10,7 |
> |
11,1 |
175 |
C 180 |
L 10/011
|
11,2 |
> |
12,0 |
200 |
C 180 |
L 10/012
|
12,1 |
> |
13,5 |
200 |
C 180 |
L 10/013
|
13,6 |
> |
16,0 |
200 |
C 180 |
L 10/016
|
16,1 |
> |
18,0 |
200 |
C 180 |
L 10/018
|
18,1 |
> |
19,5 |
200 |
C 180 |
L 10/019
|
19,6 |
> |
22,5 |
200 |
C 180 |
L 10/022
|
22,6 |
> |
25,4 |
200 |
C 180 |
L 10/026
|
25,5 |
> |
31,8 |
200 |
C 180 |
L 10/032
|
31,9 |
> |
35,5 |
200 |
C 180 |
L 10/035
|
35,6 |
> |
38,5 |
200 |
C 180 |
L 10/038
|
38,6 |
> |
41,5 |
200 |
C 180 |
L 10/041
|
41,6 |
> |
45,4 |
200 |
C 180 |
L 10/045
|
45,6 |
> |
51,5 |
200 |
C 180 |
L 10/051
|
52 |
> |
57,5 |
200 |
C 180 |
L 10/057
|
58 |
> |
64,5 |
200 |
C 180 |
L 10/064
|
65 |
> |
70,5 |
200 |
C 180 |
L 10/070
|
71 |
> |
76 |
200 |
C 180 |
L 10/076
|
77 |
> |
83 |
320 |
C 120 |
L 10/083
|
84 |
> |
89 |
320 |
C 120 |
L 10/089
|
90 |
> |
95 |
320 |
C 120 |
L 10/095
|
96 |
> |
105 |
320 |
C 120 |
L 10/105
|
106 |
> |
118 |
320 |
C 120 |
L 10/118
|
119 |
> |
127 |
450 |
C 120 |
L 10/127
|
128 |
> |
140 |
450 |
C 120 |
L 10/140
|
141 |
> |
152 |
450 |
C 120 |
L 10/152
|
153 |
> |
165 |
450 |
C 120 |
L 10/165
|
166 |
> |
178 |
450 |
C 120 |
L 10/178
|
179 |
> |
190 |
450 |
C 120 |
L 10/190
|
191 |
> |
203 |
450 |
C 120 |
L 10/203
|
204 |
> |
228 |
880 |
C 120 |
L 10/228
|
229 |
> |
254 |
880 |
C 60 |
L 10/254
|
|
Obtained roughness values:
grit C 60 = 100 up to 125 micro-inches C.L.A.
grit C 120 = 40 up to 50 micro-inches C.L.A.
grit C 180 = 30
up to 40 micro-inches C.L.A.
grit C 400 = 15 up to 25 micro-inches
C.L.A.
grit A0 800 = 8 up to 12 micro-inches C.L.A.
grains
C 800 = 8 à 12 micro-inches C.L.A.
The treated material, the
initial state of the surface, the rotation speed and the used lubrication
can alter these values which are sheer indicative. |
|
|
USE :
- Never hone dry. Use our
honing oil W03, in drops on the honing tool, or under constant sprinkle
if your machine is adapted with a lubrication circuit.
- Recommended rotation speeds
:
ø 4,5 up to ø 25 mm : ± 1200 RPM.
ø 26 up to ø 51 mm : ± 800 RPM.
ø
52 up tp ø 83 mm : ± 600 RPM.
ø 84 up
to ø 152 mm : ± 350 RPM.
ø 153 up to ø
254 mm : ± 200 RPM.
- Introduce the brush into
the piece
- During honing, give the brush a reciprocative movement.
- Wash the pieces abundantly after honing. |
|
|
|
|
|
|
|
|
|
|
|
|
The exterior diameter of a honing
brush L 10, measured «in free air», will always be superior
to the be honed ø. This is logical, because to assure
a regular honing on the 360° of the interior bore, the honing
brush must be slightly superior to the to be worked on Ø.
Without deforming risks, a brush can remove up to 0,02 mm. Not more.
|
